My Profile
Active Members
TodayLast 7 Days
more...
Awards & Gifts
Online Exams
Fresher Jobs
Our fresher job section is exclusively for fresh graduates! Find jobs for freshers in major Indian
cities including Bangalore, Chennai, Hyderabad, Pune or Kochi
Resources
Find educational articles, blogs, discussion threads and other resources.
Colleges
Find details about any college in India or search for courses.
Advertisements
|
CCNA
Posted Date: 22 Apr 2008 Resource Type: Articles/Knowledge Sharing Category: Education
|
Posted By: sac Member Level: Diamond
Rating:  Points: 5
|
|
|
1. As system administrator, you type “debug ipx sap” and receive the following lines as part of the IOS response: type 0×4, “HELLO2?, 199.0002.0003.0006 (451), 2 hops type 0×4, “HELLO1?, 199.0002.0003.0008 (451), 2 hops What does “0×4? signify?
* That is a Get Nearest Server response.
* That it is a General query.
* That it is a General response.
* That it is a Get Nearest Server request.
Correct answer: A
2. To monitor IP igrp traffic, you can use “debug IP igrp transaction” or “debug IP igrp events”. How do you display information about IPX routing update packets?
* debug routing
* debug ipx transaction
* debug ipx routing activity
* debug ipx events
Correct answer: C
3. To monitor ipx traffic on a network, what command would you use?
* debug ipx transaction
* show ipx traffic
* show ipx events
* display ipx traffic
Correct answer: B
4. What command would you use to find out the names of Novell servers on a network?
* show ipx servers
* show ipx hosts
* show ipx sap
* show ipx nodes.
Correct answer: A
5. The “ipx delay number” command will allow an administrator to change the default settings. What are the default settings?
* For LAN interfaces, one tick; for WAN interfaces, six ticks
* For LAN interfaces, six ticks; for WAN interfaces, one tick
* For LAN interfaces, zero ticks; for WAN interfaces, five ticks
* For LAN interfaces, five ticks; for WAN interfaces, zero Ticks
Correct answer: A
The default is–for LAN interfaces, one tick; for WAN interfaces, six ticks
6. As a system administrator, you need to set up one Ethernet interface on the Cisco router to allow for both sap and Novell-ether encapsulations. Which set of commands will accomplish this?
* interface ethernet 0.1 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0.2 ipx network 6c
* interface ethernet 0 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0 ipx encapsulation sap ipx network 6c
* interface ethernet 0.1 ipx encapsulation Novell-ether interface ethernet 0.2 ipx encapsulation sap
* interface ethernet 0.1ipx encapsulation Novell-ether ipx network 9e interface ethernet 0.2 ipx encapsulation sap ipx network 6c
Correct answer: D
The following commands setup the subinterfaces to allow for two types of encapsulation: interface ethernet 0.1 ipx encapsulation Novell-ether ipx network 9e interface ethernet 0.2 ipx encapsulation sap ipx network 6c
7. What does the “IPX maximum-paths 2? command accomplish?
* It enables load sharing on 2 paths if the paths are equal metric paths.
* It sets up routing to go to network 2.
* It is the default for Cisco IPX load sharing.
* It enables load sharing on 2 paths if the paths are unequal metric paths.
Correct answer: A
It enables load sharing on 2 paths if the paths are equal metric paths. The default is 1 path and the maximum is 512 paths.
8. You want to enable both arpa and snap encapsulation on one router interface. How do you do this?
* The interface can handle multiple encapsulation types with no extra configuration.
* Assign two network numbers, one for each encapsulation type.
* Enable Novell-ether to run multiple encapsulation types.
* Both arpa and snap are enabled by default so you don’t have to configure anything.
Correct answer: B
To assign multiple network numbers, you usually use subinterfaces. A sample configuration follows: ipx ethernet 0.1 ipx encapsulation novell-ether ipx network 9e interface ethernet 0.2 ipx encapsulation sap ipx network 6c
By default, Cisco routers forward GNS SAPs to remote networks.
* False
* True
Correct answer: A
GNS is Novell’s protocol to Get Nearest Server. If there is a server on the local network, that server will respond. If there isn’t, the Cisco router has to be configured to forward the GNS SAP.
9. To prevent Service Advertisements (SAPs) from flooding a network, Cisco routers do not forward them. How are services advertised to other networks?
* Each router builds its own SAP table and forwards that every 60 seconds.
* Each router assigns a service number and broadcasts that.
* SAPs aren’t necessary with Cisco routers.
* Cisco routers filter out all SAPs.
Correct answer: A
Cisco routers build SAP tables and forward the table every 60 seconds. All SAPs can’t be filtered even with 4.x since NDS and time synchronization uses SAPs.
10. Novell’s implementation of RIP updates routing tables every ____ seconds.
* 60
* 90
* 10
* 30
Correct answer: A
Novell’s RIP updates routing tables every 60 seconds, Apple’s RTMP is every 10 seconds, routers ARP every 60 seconds, IGRP signal every 90 seconds, and Banyan VINES signals every 90 seconds.
|
Responses
|
No responses found. Be the first to respond and make money from revenue sharing program.
|
|
|