Resources » Articles/Knowledge Sharing » Education

5 Different Combustion Chambers Of Diesel Engines.


Posted Date: 05-May-2009  Last Updated:   Category: Education    
Author: Member Level: Gold    Points: 25


Read this one for 5 Different Combustion Chambers Of Diesel Engines.



When we are going to design the combustion chamber of diesel engines the main consideration we have to keep in mind is, high compression ratio & sufficient turbulence of air. For high compression ratios overhead valves are more preferred than side valves. Below are the some shapes of combustion chambers discussed.

01) Open or Direct Injection Chamber
For moderate & low speed engines this type of combustion chamber is most suitable. The fuel is injected directly in the combustion chamber which is
formed by a part of the piston, where it penetrates the mass of hot compressed air. The injector pressure is more than 21 kilogram per centimeter square
is used. The fuel injector is placed in the center of the chamber and contains more than four orifices. Due to location of orifices the spray pattern suits the combustion chamber & does not impinge on the wall of the cylinder or piston.

This design is used by Leyland Motors Ltd has the chamber in the form of a truncated cone and the fuel injector is located near the circumference of the
chamber. In some engines two injectors are located on the opposite side of the chamber. The open type of combustion chamber depends upon the primary
turbulence as the main source of air movement due to which engine can start in cold condition and don't required heater plug.

02) Auxiliary Combustion Chamber
In small high-speed engines, this type of combustion chamber is mostly used. Total fuel is directly fed into an auxiliary combustion chamber where the
initial combustion takes place. Due to rise in pressure the partially burnt mixture is forced at high velocity through a small orifice into the main combustion chamber where the rest of the combustion aided by secondary turbulence takes place.

As the piston descends during power stroke, the pressure difference created between the precombustion chamber and the main chamber assists in discharging the hot exhaust gases from the precombustion chamber.This type of combustion chamber has very low maintenance cost due to low injection pressure and simpler single nozzle orifice. The main combustion chamber is subjected to less pressure since the pressure shock is mainly taken by precombustion chamber. This type of combustion chamber gives clean exhaust but heat losses are higher due large surface area of two chambers.

03) Air Cell
In some designs small chamber is provided which is called as air cell. They are away from the fuel spray nozzle, which is so located that the fuel is sprayed
near the narrow neck, which connects the air cell with the main combustion chamber. Piston compresses the air during compression stroke and pushes it
into air cell. As the piston moves down the pressure in the cylinder falls resulting in the flow of hot air from the cell into the combustion chamber producing the secondary turbulence, which mixes the air & fuel further and completes the combustion. The air cell also requires a high compression ratio and heater plugs for starting. The heat losses are more due to large wall area.

04) Ricardo Comet Chamber
This combustion chamber is separated from the cylinder and one of the most efficient combustion chamber. In this type chamber air enters in tangential
direction during compression stroke and imparts a rotary motion. The fuel is then injected into the hot compressed air and the combustion takes place.
Reversal of flow takes place due to pressure rise and the hot gases are discharged into the cylinder pushing the piston upward in working stroke. Due to
higher temperature of air in the combustion chamber, fuel of low ignition quality can also be burnt satisfactorily.

05) Energy Cell
It is also called as Lanoxa chamber and works on combined principles of air cell & auxiliary combustion chamber. As the fuel is sprayed by fuel injector,
10% of fuel passes across the combustion chamber & enters in energy cell. The combustion generally starts in the main chamber, spread to the energy cell
where pressure rise considerably. Due to pressure difference between the energy cell & main combustion chamber, the hot gases from the minor cell, will
sweep the fuel from the minor cell, into the combustion chamber where additional turbulence is set up to ensure complete combustion of fuel.

A restricted opening can be closed by plunger, which connects major cell with the minor cell, this effects smooth starting. Once the engine is started the
restricted opening can be opened out so that the minor cell is connected with the major cell. Through a small opening, minor cell communicates with
combustion chamber. Due to this small opening the hot gases are throttled and so the pressure rise in main combustion cahmber is gradual. Since the fuel
is sprayed direct in to the main combustion chamber where the air has highest temperature resulting in complete combustion.


This resource is originaly published on my blog under link,http://mechanicalguru.blogspot.com/2009/05/different-combustion-chambers-provided.html


Reference: http://mechanicalguru.blogspot.com/


Did you like this resource? Share it with your friends and show your love!




Responses to "5 Different Combustion Chambers Of Diesel Engines."

No responses found. Be the first to respond...

Feedbacks      

Post Comment:




  • Do not include your name, "with regards" etc in the comment. Write detailed comment, relevant to the topic.
  • No HTML formatting and links to other web sites are allowed.
  • This is a strictly moderated site. Absolutely no spam allowed.
  • Name:   Sign In to fill automatically.
    Email: (Will not be published, but required to validate comment)



    Type the numbers and letters shown on the left.


    Submit Article     Return to Article Index

    Awards & Gifts
    Active Members
    TodayLast 7 Daysmore...

    ISC Technologies, Kochi - India. Copyright © All Rights Reserved.