Posted Date: 17 May 2019      Posted By:: Abhishek    Member Level: Silver  Points: 3 (₹ 2)

# 2017 Jawaharlal Nehru Technological University, Hyderabad B.Tech. Civil Engineering B.Tech 1st year Examination, Engineering Drawing, May/June-2017, Jawaharlal Nehru Technological University Hyderabad Question paper

 Course: B.Tech. Civil Engineering University/board: Jawaharlal Nehru Technological University, Hyderabad

Are you curious to know the previous years questions of Engineering Drawing of JNTUH ? Then you are at Right platform. Here are some questions. These are common to B.Tech 1st year ECE, EIE, ETM branches

University: Jawaharlal Nehru Technological University, Hyderabad
Paper code: 111AG
Subject: Engineering Drawing
Year of Examination : May/June- 2017
Course: Common to B.Tech ECE, EIE, ETM

Time: 3 hours Max. Marks: 75
All questions carry equal marks

1.
a) Construct a plain scale of RF=1/40 to read meters and decimeters. Maximum length to be measured using it is 5 meters. Mark on it a distance of 3.4 m. [7]
b) Draw an involute of a circle of 50 mm diameter. Also draw a normal and a tangent at a point distant 100 mm from the centre of the circle. [8]
(or)

2.
a) The distance between two places is 240 km and its equivalent distance on map measures 12cm. Draw a diagonal scale to indicate 273 km and 128 km. [7]
b) A point moves such that the sum of its distances from two fixed points 100 mm apart is always constant and is equal to 140 mm. Draw the locus of the point, the tangent and normal to the curve at any point on it. [8]

3.
a) A point A is in the HP and 25 mm in front of VP. Another point B is also in HP and behind VP. The distance between their end projectors is 55mm. Draw its Projections when the line joining their plans makes an angle of 500 with reference Line. Also find the distance of the point B from the VP [8]
b) A line AB is 85mm long has its end A 25mm away from both the reference planes and is in the first quadrant. The line is inclined at 500 to HP and 300 to VP. Draw its projections and mark the traces of the line. [7]
(or)
4.
a) A line AB is 80 mm long and it has end 20 mm above HP and 25 mm in front of VP. The line is inclined at 450 to HP and 350 to VP. Draw its projections. [7]
b) A straight line PQ has its end P 20 mm above the H.P and 30 mm in front of the V.P and the end Q is 80 mm above the H.P and 70 mm in front of V.P. If the end projectors are 60 mm apart, draw the projections of the line. Determine its true length and true inclinations with the reference planes. [8]

5. A hexagonal pyramid, base 25 mm side and axis 55 mm long, has one of its slant edges on the ground. A plane containing that edge and the axis is perpendicular to the H.P. and inclined at 450 to the V.P. Draw its projections when the apex is nearer the V.P. than the base. [15]
(or)
6. A square prism, base side 40 mm, axis 80 mm long has its base on the H.P. and its faces equally inclined to the V.P. It is cut by a plane, perpendicular to the V.P. inclined at 600 to the H.P. and passing through a point on the axis, 55 mm above the H.P. Draw its front view, sectional top view and another top view on an A.I.P. parallel to the section plane. [15]

7. A cylinder of base diameter 50 mm and axis length 60 mm is resting on HP on its base, cut by a plane inclined at 550 to HP and perpendicular to VP. The cutting plane is passing through a point on the axis at a distance 30mm from the top end. Draw the development of the lateral surface of the remaining portion of the cylinder. [15]
(or)
8. A cylinder of 50 mm diameter stands vertically with its base on HP. It is completely penetrated by an cylinder of 50 mm diameter. The axis of the penetrating cylinder is parallel to VP, inclined at 300 to HP and bisects the axis of the vertical cylinder. Draw the curves of intersection [15]

9. A sphere of radius 20 mm is kept on the top face of a square prism of side of base 40 mm and height 20 mm. The latter is placed on the top face of a cylinder of 65 mm diameter and 25 mm height. All the three solids have the common axis. Draw the isometric projection of combination of solids. [15]
(or)
10. Draw the front view, top view and left-side view of the object given in figure (1.1). All dimensions are in mm. [15]

Attachments:

### Related Question Papers:

• ENVIRONMENTAL STUDIES, May - 2017 JNTUH, Electrical and Electronics Engineering, B. Tech III Year II Semester Examinations

• PHARMACEUTICAL BIOTECHNOLOGY, B. Pharmacy IV Year II Semester Examinations-May-2017, Code No: R7, JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD702,

• PHARMACEUTICAL BIOTECHNOLOGY, B. Pharmacy IV Year II Semester Examinations-May-2017, Code No: R7, JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD702,

• PHARMACEUTICAL BIOTECHNOLOGY, B. Pharmacy IV Year II Semester Examinations-May-2017, Code No: R7, JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD702,

• June 2011 Jawaharlal Nehru Technological University Electronic Devices and Circuits Model Question paper

• ### Categories

Submit Previous Years University Question Papers and make money from adsense revenue sharing program

Are you preparing for a university examination? Download model question papers and practise before you write the exam.

Looking for University or College admissions in India for 2020 - 2021 Academic Year?

Top Contributors
TodayLast 7 Daysmore...